Indiana

23.2.2021

INDIANA

IN_500

Author : Ivana Skalská

Bracelet and earrings Indiana from new Arrow beads are sewn two needles. I hope this does not deter you, because their networks are not demanding and beautiful them stand out geometric shapes.

Materials and tools:

Needle - 2

pliers - preferably two

solid stringing material - FireLine

DIAMONDUO - 16 pieces (bracelet) + 6 pieces (earrings) - a total of 22 pieces (hereinafter DD)

ARROW - 30 pieces (bracelet) + 8 pieces (earrings) - A total of 38 pieces (hereinafter referred to as A)

Polished beads 4 mm - 30 pieces (bracelet) + 8 pieces (earrings) - A total of 38 pieces (hereinafter FP4)

Polished beads 3 mm - 28 pieces (bracelet) + 4 pieces (earrings) - A total of 32 pieces (hereinafter FP3)

Miyuki Delica 11/0 - pack 5 grams (hereinafter MD11) (NOT REPLACE TOHO 11/0)

Ring - 4 units (bracelet) + 2 pieces (earrings) - a total of 6 pieces

Carabiner - 1 pc

The counter - 1 pc

Earwires - 2

Bracelet

The length of the bracelet clasp 17.7 cm; without closing rings and 15.5 cm. The width of 1.5 cm.

Adding one bead bracelet Diamonduo extend about 1 cm.

Cut a thread of about 2 m long. The two ends of the thread the needle. Thread 1 And the first hole, the second hole DD 1 and 1 A first hole (let the whole time sewing sure you have correctly DD face and reverse side) and move the beads into the center of the thread (Fig. 1). Thread the right needle and sew 1x FP4 A second hole, thread 1x DD and sew the first hole and second hole and the second (Fig. 2).

IN1

IN2

Thread the left needle and sew 1x FP4 A second hole, the first hole sew DD added in the previous step and sew the second and the second hole (Fig. 3). All well tighten. Put the right needle 1 MD11, FP3 1x, 1x and 1x MD11 And the first hole. DD stitch and wrap the second hole and the first hole. (Fig. 4).

Put the needle on the left MD11 1x, 1x FP3, 1 MD11 and sew just added And the first hole, the second hole DD and the second just added And the first hole. (Fig. 5). Repeat steps 2-5 to the desired length. In my case, I used a 16 DD. Margins are a little wavy, but do not worry, you'll still sew. They are larger in size, so do not go Jimy Miyuki Delica replace.

After reaching the required yarn length based on the second buttonhole beads A (Fig. 6.7).

Now the vocal edge bracelet. Left needle sew FP4, MD11, MD11 and FP3 (Fig. 8). Step 8 Repeat the entire length of the bracelet. Sew the last remaining FP4. Sewing can provide during quilting few knots. Repeat for the right needle. You now have a bracelet paved, twists based on recent FP4 beads. (Fig. 9). Zapošijte and cut off the ends.

Holes in the free end by means of two DD Thread clamp ring and via a second ring and counterring attach karabiner (Fig. 10). Now you have finished bracelet (Fig. 11).

And if you fancy, you can start even in the production of earrings.

Earring

Length earrings afro hooks 4.5 cm, width 1.5 cm.

Cut a long thread about 50 cm. At both ends of the thread the needle. Thread 1 And the first hole, the second hole DD 1 and 1 A first hole (let the whole time sewing sure you have correctly DD face and reverse side) and move the beads into the center of the thread (Fig. 1). Thread the right needle and sew 1x FP4 A second hole, thread 1x DD and sew the first hole and second hole and the second (Fig. 2).

IN13

IN14

IN15

IN16

Put the needle on the left MD11 1x, 1x FP3, 1 MD11 and sew just added And the first hole, the second hole DD and the second just added And the first hole. (Fig. 5). Thread the right needle and sew 1x FP4 A second hole, thread 1x DD and sew the first hole and second hole and the second (Fig. 6).

IN17

IN18

Thread the left needle and sew 1x FP4 A second hole, the first hole sew DD added in the previous step and sew the second and the second hole (Fig. 7). All well again tighten. Both ends of the yarn based on the second hole A (Fig. 8).

IN19

IN20

Sew beads gradually all sides earring (FP4, MD11, FP3, FP4 and MD11). Now you have an earring tailored, based on recent threads beads FP4. (Fig. 9). Both ends of the yarn zapošijte, cut off, and you are done (fig. 10).

IN21