ANASTACIA necklace

23.2.2021

ANASTACIA

Design: Karla Mokrošová

Beading Components and Tools:

Beading needle – 1 piece

Firm stringing material – FireLine, S-lon or Nymo Beading Thread

Swarovski Xilion Beads size 4 mm – 12 pcs (S4), can be used Fire Polished Beads 4 mm,

M.C. Beads 4 mm

Swarovski Xilion Beads size 3 mm – 16 pcs (S3), can be used Fire Polished Beads 3 mm,

MC Beads 3 mm

TOHO Beads 11/0 – 1 packing 10 g (T 11/0)

TOHO Beads 8/0 – 4 pcs (T 8/0)

Stainless Steel Ring or Nylon Cord with screw snap – 1 piece

ZOLIDUO right – 24 pcs (ZR)

ZOLIDUO left – 24 pcs (ZL)

Ring – 1 piece

Runner – 1 piece

Pliers

Scissors

Beading Mat

Diameter of the Stainless Steel Ring 140 mm. Length of the pendant 7 cm, width 6,3 cm.

Cut the thread about 1,80 m long. Leave ca.20 cm of the thread free at the end to be sewn in.

The base is made of the couple of right and left Zoliduo Beads which have to be turn by reverse sides to each other.

String 1x T 11/0, 2x ZL, 1x T 11/0, 2x ZR on one end. Keep the same rank of the beads and string them 3x (picture 1). Sew through these strung beads in the same rank into the circle.

Knot the threads, sew in the shorter end and cut it. The needle comes from T 11/0 at the end (picture 2).

Sew through lower hole of following ZR (picture 3). Sew through upper hole of the same ZR (picture 4).

String 1x ZR through lower hole, 1x T 11/0, 1x ZL through lower hole and sew through upper hole 2x ZL (picture 5). String 1x S4 and sew through upper hole 2x ZR (picture 6). Repeat the procedure according to the pictures 5 and 6 until the end of the row.

Sew through 2x ZR with the last stringed S4 (picture 7). Sew through lower hole 1x ZR, 1x T 11/0 and through lower hole 1x ZL (picture 8).

Sew through upper hole 2x ZL and 1x S4 (picture 9). String 1xT 11/0 2x ZL through lower hole and sew through upper hole 1x ZR (picture 10).

String 1x ZR through lower hole, 1x T 11/0, 1x ZL through lower hole and sew through upper hole 1x ZL (picture 11). String 2x ZR, 1x T 11/0 and sew through 1x S4 (picture 12).

String 1x T 11/0, 2x ZL and sew through upper hole 1x ZR (picture 13). Repeat the procedure until the end of the row. Sew through 1x S4, 1x ZL through lower hole with the last stringed 2x ZR and 1x T 11/0 (picture 14).

Sew through upper hole the same ZL (picture 15). String 1x T 11/0 and sew through upper hole the following 1x ZR (picture 16).

String 1x S3 and sew through upper hole the following 1x ZR (picture 17).

String 1x S3 and sew through upper hole 1x ZL (picture 18).

String 1x S4, 1x T 8/0, 1x S4 and sew through upper hole 1x ZR (picture 19).

String 1x S3 and sew through upper hole 1x ZL (picture 20).

String 1x S3 and sew through upper hole 1x ZL (picture 21).

String 1x T 11/0 and sew through upper hole 1x ZR (picture 22).

Repeat the procedure until the end of the row.

You finish the outstanding end of the row. String 1x S3 and sew through upper hole 1x ZL picture 23). String 1x S3 and sew through upper hole 1x ZL (picture 24).

Sew through once again all the last strung beads into the circle in order to get firmer. Sew in the thread and cut it (picture 25). The pendant is ready. Fasten the ring with the runner into T 8/0 and hang them on the ring (picture 26).